RDM EC7000i Installationsanleitung

EC6000i®, EC7000i®, and EC7500i® Series Installation Guide

8Inside ComponentsCover LatchImage Frame in raised positionOutside Cover in raised positionImage SensorDocument Feed Plate comes out to reveal optiona

9Connection PortsRDM’s EC6000i, the EC7000i, and EC7500i can be installed in different configurations. These configurations are set and programmed by

10D. Insert the Franking Acknowledgement Printer Cartridge (Optional)The Franking Acknowledgement Printer Cartridge is an optional ink stamp, that mar

11II. Insert the Franking Acknowledgement Printer Cartridge into the Printer Assembly1. Insert the Franking Acknowledgment Printer Cartridge straigh

12E. Connect to a Telephone Line (EC6014 and EC7014)FOR TEL: If you have purchased the EC6000i or the EC7000i with the optional modem, follow these di

13F. Connect the Power Cord1. Insert the round end of the power cord into the power port on the back of the scanner.2. Align the flat side of the powe

14G. DriversThe drivers for your scanner are installed when you install your PC application. If it is a Web-based application, ActiveX may be installe

15Operating the ScannerPreparing ChecksTo reduce the possibility of errors and damage to the unit, you should: • Remove all folds and creases in the c

16Status Signals for EC6000i and EC7000iThe scanner comes equipped with the default light and sound signals described below. EC6000i/EC7000i Default L

17EC6000i/EC7000i Default Sound SignalsSeveral conditions are also signaled by a pattern of tones in addition to the LED display.A Typical Check Proce

This manual, the EC6000i , EC7000i, and EC7500i Series Installation Guide, is intended for all units belonging to the EC6000i, EC7000i, and EC7500i fa

18Status Signals for EC7500iThe scanner comes equipped with the default light and sound signals described below. Default Light Signals for EC7500iThe

19EC7500i Beeper CuesSingle short beep - Indicates that a scanning exception or error has occurred. Check the scanning application display for instruc

20Maintaining the EC6000i, EC7000i, or EC7500iThe EC6000i, EC7000i, or EC7500i performs best when all working surfaces are clean and free of foreign m

21Cleaning the ImagerOccasionally, it may be necessary to clean the image sensors and remove dust or debris from the interior of the EC6000i, the EC70

22TroubleshootingIn the course of everyday operations, you may encounter minor malfunctions in the EC6000i, the EC7000i, or the EC7500i unit. Before c

23 Check Feeder Does Not Function Properly Ensure that you are inserting the check properly: flush to the right side of the EC6000i, the EC7000i, or t

24Card Transactions Do Not Function Properly Test the Card Swipe Mechanism1. Ensure that you are swiping the card properly. The black magnetic stripe

25SpecificationsEC6000i, EC7000i, EC7500i SpecificationsUnit Size Without MSR 8.6″ long x 6.1″ wide x 4.4″ high21.9 cm long X 15.4 cm wide X 11.3 cm h

26EnvironmentalOperating Temperature 32 to 104 degrees F (0 to 40 degrees C).Operating Humidity 10 to 85% relative humidity (non-condensing).Document

27(Optional) Modem SpecificationsSupports V.34bis, V.34 V.F.C, V.32bis, V.32, V.22bis, V.22A/B, V.23, V.21, Bell 212A and 103Error Correction V.42 LAP

1ContentsCompliance Statements ...2Introduction ...

28Warranty InformationLIMITED WARRANTY: The RDM EC6000i units are warranted against defects in materials and workmanship under normal use and service

29WARRANTY SPECIFICS: This warranty only covers failures due to defects in materials or workmanship, which occur during normal use. It does not cover

2Compliance StatementsFCC Compliance StatementNOTE for EC6000i , EC7000i, and EC7500i Series Scanners: This equipment has been tested and found to com

3The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipment. If

4IntroductionThe EC6000i®, the EC7000i®, and the EC7500i® Series Scanners are cost effective, feature rich, imaging solutions. Using RDM’s industry l

5Requirements• The EC6000i, the EC7000i, and the EC7500i units are for indoor use only. Keep the EC6000i, the EC7000i, and the EC7500i dry; avoid area

6Setting Up the EC6000i, EC7000i, or EC7500iTo set up the EC6000i, the EC7000i, and the EC7500i, follow steps A – H.A. Choose a LocationLocate your sc

7C. Inspect the Unit’s FeaturesThe illustrations below show a basic scanner (Model A), and an EC7500i scanner with a Magnetic Stripe Reader (MSR) and